ATA8741-PXQW【PDF 39/238 页】MCU W/TRANSMITTER ASK/FSK 24QFN

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录52

35页 36页 37页 38页 [39页]40页 41页 42页 43页

9140CINDCO02/10

ATA8741

" Bit 7 Res: Reserved Bit

This bit is reserved for future use and will always read as 0 in ATtiny24/44/84. For compatibility

with future AVR devices, always write this bit to zero. After reading, mask out this bit.

" Bit 6 Res: Reserved Bit

This bit is reserved in the ATtiny24/44/84 and will always read as zero.

" Bits 5, 4 EEPM1 and EEPM0: EEPROM

Mode Bits

The EEPROM Programming mode bits setting defines which programming action that will be

triggered when writing EEPE. It is possible to program data in one atomic operation (erase the

old value and program the new value) or to split the Erase and Write operations in two different

operations. The Programming times for the different modes are shown in Table 13-1. While

EEPE is set, any write to EEPMn will be ignored. During reset, the EEPMn bits will be reset to

0b00 unless the EEPROM is busy programming.

" Bit 3 EERIE: EEPROM Ready Interrupt Enable

Writing EERIE to one enables the EEPROM Ready Interrupt if the I-bit in SREG is set. Writing

EERIE to zero disables the interrupt. The EEPROM Ready Interrupt generates a constant inter-

rupt when Non-volatile memory is ready for programming.

" Bit 2 EEMPE: EEPROM Master Program Enable

The EEMPE bit determines whether writing EEPE to one will have effect or not.

When EEMPE is set, setting EEPE within four clock cycles will program the EEPROM at the

selected address. If EEMPE is zero, setting EEPE will have no effect. When EEMPE has been

written to one by software, hardware clears the bit to zero after four clock cycles.

" Bit 1 EEPE: EEPROM Program Enable

The EEPROM Program Enable Signal EEPE is the programming enable signal to the EEPROM.

When EEPE is written, the EEPROM will be programmed according to the EEPMn bits setting.

The EEMPE bit must be written to one before a logical one is written to EEPE, otherwise no

EEPROM write takes place. When the write access time has elapsed, the EEPE bit is cleared

by hardware. When EEPE has been set, the CPU is halted for two cycles before the next

instruction is executed.

" Bit 0 EERE: EEPROM Read Enable

The EEPROM Read Enable Signal EERE is the read strobe to the EEPROM. When the cor-

rect address is set up in the EEAR Register, the EERE bit must be written to one to trigger the

Table 13-1. EEPROM Mode Bits

EEPM1

EEPM0

Programming

Time

Operation

3.4 ms

Erase and Write in one operation (Atomic Operation)

1.8 ms

Erase Only

1.8 ms

Write Only

Reserved for future use

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式